top of page
This site was designed with the
.com
website builder. Create your website today.Start Now

Primary Researcher

  • A Study of The Machinability of Titanium Alloys - FRGS/2008/FKP (2)/F00067 RM80,000 (Completed)

  • A study on microstructural evolution and mechanical behaviour of stainless steel structure produced by a novel approach of shape metal deposition – FRGS/2010/FKP/TK03/7 – F00105 RM47,300 (Completed)

  • Effect of the novel biodegradable resin bonded sand mould conditions on the Al-Si alloy casting properties - PJP/2011/FKP(30A)/S00996 RM12,500 (Completed)

  • Mechanical Properties of Aluminum Alloy 1050 H24 by Localized Laser Heat Treatment – PJP/2012/FKP(1B)/S01093 RM25,500 (Completed)

  • Effect of Deposition Process on Properties of Nickel-based Alloy Clad on Cast Iron Trim Cutter – RAGS/2012/UTEM/TK01/4 B00015 RM80,00 (Completed)

  • Process-Properties Characterization of Repetitive Repair Welding on Stainless Steel to Carbon Steel Orbital Pipe Joints – FRGS/2015/TK03/FKP/02/F00280 RM149,00 (Completed)

  • Prototype Development of Ergonomics Grinding System to Bevel a Pipe in Preparation for Welding - PJPC/2020/FKP-COSSID/SC0002 RM20,000 (Completed)​​

  • Large Volume Additive Manufacturing (LVAM) Consortium - KHAS-KKP/2021/FKP/C00006 RM138,00 (Completed)​

Co-Researcher

  • Development of a Cooling System in a Copper Fixture for WAAM of Alumnium Alloys - PJP/2022/FKP/S01876  RM20,000 (On-going)

  • Investigation of the Tungsten Carbide Morphology Behaviour due to In-situ atomic Level Etching using Pulse and DC Substrate Bias Voltage – FRGS/2010/FKP/SG02/8/F00110 (Completed)

  • Formulating the Machining Process Capability of Machine Tool using Statistical Analysis of the Machine Rigidity - FRGS/2011/FKP/TK03/1/F00116 (Completed)

  • The effect of aspect ratio and oxide scale to the development of subsurface layer for aluminium alloys (3xxx & 5xxx) during the hot rolling process - PJP/2011/FKM(25A)/S00980 (Completed)

  • A Novel Study On The Effects Of Cutter Geometrical Feature In Component Failure For Machining Thin-Wall Low Rigidity Structural Component - FRGS/2012/FKP/TK01/03/2/F00134 (Completed)

  • Super Energy Saving Locking System – GLUAR/2012/FKP(1)/G00010 (Completed)

  • Design and Analysis of Fractional-Slot Permanent Magnet Brushless Machine For Electric Vehicle Application - PJP/2012/FKE(53A)/S01060 (Completed)

  • Modified of cooling system of dumbbell injection mould: reducing of warpage defect - PJP/2012/FKP(25B)/S01028 (Completed)

  • Effect Of Gas Metal Arc Welding Parameters On Microstructural and Mechanical Properties of the Tailor Welded Orbital - PJP/2012/FKP(2B)/S01094 (Completed)

  • Improving the Machinability of AISI D2 using Hybrid Machining for Metal Stamping Industry – RAGS/2012/FKP/TK01/1 B00012 (Completed)

  • PJP/2014/FKM(1B)/S01294 (On-going)

  • MTUN-COE 2012 (UTEM,UTHM,UMP)

  • Experimental analysis and simulation on the distortion of thin and high strength steel welded using a new cold arc welding technique – FRGS/2017

  • Improved Tool Steels Alloy Through Double Austenization in Reducing Surface Roughness and White Layer with Wire Electrical Discharge Machining (WEDM)

bottom of page